Support For DJI Mic

It is recommended to use a 5V/2A charger to charge the transmitters, receiver, and Charging Case. At room temperature, it takes about 1 hour and 10 minutes to fully charge the transmitters and receiver using the Charging Case. To fully charge the Charging Case, it takes about 2 hours and 40 minutes.

It is recommended to use the Back Clip to attach DJI Mic to locations such as a shirt collar, or it can be used with the Clip Magnets. Note: If you need to put the transmitters on any flat surface, use the Clip Magnets to make them stand upright.

Omnidirectional.

1. Download the firmware update package from the official DJI website Download page.
2. Connect the transmitters and receiver to your computer using a standard USB-C cable.
3. Put the downloaded firmware update package (the file with "bin" as a suffix) under the root directories of the transmitters and receiver.
4. Disconnect from your computer and the transmitters and receiver will start the firmware update automatically.
Note: If an update fails, download and copy the firmware again and reboot the transmitters and receiver. Repeat until the firmware update is successful.

250 meters with FCC compliance in open environments without interference.

DJI Mic transmitters and receiver are already linked by default. If you need to link them again, you can do so in the following ways:
Method 1: Put the transmitters and receiver into the Charging Case and they will link automatically.
Method 2: Turn on the receiver and transmitters. Scroll down on the screen of the receiver to enter the control center page. Slide to the left and click “Settings” to enter the settings page. Slide to the left again and click “Link” to enter linking mode. Then, press and hold the link button on the side of the transmitters until the green light on the top left corner flashes and wait for the linking to finish. When the linking indicators of the transmitters turn solid green, it means linking is successful.
To end linking, click “Stop Linking.”

Yes. DJI Mic transmitters support standalone recording. Press the recording button on the side of the transmitters. A solid red light indicates that recording has started. When fully charged, it can record for up to 5.5 hours. With a constant power supply, it can record up to 14 hours of 24-bit lossless audio. Note: Audio will be saved as one file for every 30 minutes during standalone recording. When internal storage space runs out, new audio will replace the earliest ones, and new files will also be saved every 30 minutes.

You can export the audio by connecting the transmitters to your computer using a standard USB cable.

After linking the transmitters with the receiver, slide the main screen of the receiver upward, click the Mic icon, and you can mute or unmute the transmitters. You can also double press the mute button of the transmitters. The mute indicator will pulse red to show that the transmitters are muted.

No.

DJI Mic transmitters have built-in 8GB storage and do not support external storage.

You can delete audio files by connecting the transmitters to your computer. To delete all files you can use the receiver directly.

No.

No. The transmitters only support the receiver of DJI Mic.

Mount the windscreen into the slots on the transmitters, then press and turn clockwise to tighten.

No. It only supports DJI Mic transmitters.

It can connect with up to two transmitters at the same time.

To connect with a smartphone: Insert the standard phone adapter into the pogo-pin port at the bottom of the transmitters and connect with your phone. Start shooting or recording on your phone and the receiver will start working.
To connect with a camera: Transmitters can be mounted on camera hot shoes via hot shoe adapter plates. Use a 3.5mm camera connection cable to connect the camera mic port and the 3.5mm audio output port on the receiver. Then, start recording videos on your camera and the receiver will start working.
To connect with a computer: Use a 3.5mm camera connection cable to connect the mic port of your computer with the 3.5mm audio output port of the receiver. Start recording on your computer and the receiver will start working.

Under M mode, the audio recorded by the two transmitters will be in one channel; under S mode, the audio will be separate in the left and right channels.

Link the transmitters and receiver and plug the 3.5mm earphone jack into the 3.5mm monitor port of the DJI Mic receiver and you can begin monitoring. You can also adjust monitoring volume. Slide the main screen of the receiver downward to enter the settings page. Slide to the left and click monitor gain to adjust the volume.

2.4GHz private protocol.

S: Stereo;
M: Mono;
Ms: Mono with Safety Track on
Note: If you use Safety Track, you need to separate the tracks during post-production.

You can lock the receiver screen by pressing the power button for one second and a lock icon will appear on the screen. Press again and you can unlock the screen.

No.

No.

Yes.

As this product contains magnets, it is recommended to keep it away from bank cards, pacemakers, RAM chips, and hard discs.

1. DO NOT use when wearing thick or heavy clothing (sweaters, down jackets, etc.). The transmitters could fall off due to lack of magnetic connection.
2. DO NOT use when performing strenuous exercises such as running or jumping.

The transmitter and receiver are already linked by default and ready to use after powering on. If you need to link them again, first turn on the receiver and transmitter. Scroll the screen of the receiver downward to enter the control center page. Slide to the left and tap “Settings” to enter the settings page. Slide to the left again and tap “Link” to enter linking mode. Then, press and hold the link button on the side of the transmitter until the green light on the top-left corner flashes and wait for the linking to finish. When the linking indicators of the transmitter turn solid green, it means the linking is successful. To end linking, click “Stop Linking.”

It is recommended to use a 5V/2A charger to charge the transmitter and receiver. At room temperature, it takes about 1 hour and 10 minutes to fully charge the transmitter and receiver using the splitter charging cable.

Yes.

The receiver supports Stereo mode, but requires an additional transmitter.

DJI Mic (1 TX + 1 RX) is ideal for vlogs, livestreaming, and interviews.