Support for Osmo

There is a built-in mic in the Osmo. To improve the recording, a 3.5mm interface and external mic can be attached. The following microphones are compatible with the Osmo: Sennheiser MKE400, Sony ECM DS70P, Rode VideoMic Pro, Rode VideoMicro, Mymyk Smartmyk, and DED DV-889.

No.

Yes. There will be no sound during playback from the Osmo, but the sound will be available when the file is opened from the media library.
To save a video with audio, the video must be longer than 7 seconds.

No, the power consumption for 5.8GHz is higher.

Hold the Osmo upside down for two to three seconds then shut it down and detach the camera. Attach the camera onto the Inspire again and the image will be oriented correctly.

After updating the Zenmuse X3 camera firmware to 1.4.0.10 or higher on the Inspire 1, you can install the X3 camera directly on the Osmo.

The standard Osmo battery reaches 980mAh, 11.1V, and 10.8Wh. A high-capacity version of the battery is also available.

Up to 60 minutes.

The LED indicator on the charger will be solid green when in standby and solid red during charging. When charging is complete, it will go from red to green.

Yes. After updating the Zenmuse X3 camera firmware on the Inspire 1, you can install the X3 camera directly on the Osmo.
But you cannot use the Osmo camera on the Inspire 1 due to the compatibility issue.

No.

It takes about 60 minutes to charge the battery, and the Osmo Intelligent Battery has overcharge protection. When charging is complete or the battery is charging abnormally, it will stop charging automatically, so you don’t need to remove the battery once it’s fully charged.

Remove the gimbal cover and lens cover, then remove the handle cover and rosette mount cover.
Rotate the Gimbal Lock to the unlocked position on the handle (align the white mark on the Gimbal Lock with the white line on the handle). Align the white line on the gimbal with the red line on the handle and insert. Make sure there is good contact between the gimbal and the Gimbal Lock.
Rotate the Gimbal Lock so that both white marks align to lock the gimbal in place. Check to make sure the gimbal is mounted securely.

Lock the pitch and roll axis first and then lock the pan axis.

Align the base of the mobile device holder with the rosette mount.
Turn the dial to tighten the mount against the Osmo handle.

1. Release the clamp arm on the mobile device holder.
2. Adjust the clamp positions.
3. Insert one side of the mobile device into the clamp.
4. Push the device to extend the holder then insert the other side of the mobile device.
5. Release the holder.

The gimbal is locked in three axes to protect its motors. To unlock:
1. Twist the tilt motor until it can rotate freely.
2. Repeat with the roll motor.
3. Slide the Pan axis Lock up to unlock the pan axis.
● Be sure to unlock the tilt motor before unlocking the roll motor to avoid damaging the camera lens.
● Rotate the motors just enough to allow free motion.

Pull the power switch down for 1.5 seconds and then release it to power on the Osmo.

When the Osmo is switched on, pull down and release the power switch to enter hibernation.
Repeat awaken.

Power on the Osmo.
On your mobile device, connect to the ‘OSMO_XXXXXX’ Wi-Fi network.
Enter the password: 12341234, then launch the DJI GO App on your mobile device.
Find OSMO in the App and enter Camera View.

Tap the playback button in Image Transmission Settings.

In DJI GO app, go to: Settings > Gimbal > Roll Axis Adjustment.
Positive values rotate the gimbal clockwise. Negative values rotate the gimbal counterclockwise.

Please refer to the following video:
https://www.skypixel.com/videos/d274d41b-2166-4651-9241-fe0813ff42e2

The Osmo shoots 4K video in MP4 and MOV formats. Select the format in DJI GO - Settings - Video Format.

Switch to the external network when activating the Osmo. Enter your email account, click “Activation”, and switch to the Wi-Fi. For details, refer to the following link:
http://www.djivideos.com/video_play/a34c4e61-6916-401e-8ce7-75e148791090

The Osmo’s sounds cannot be switched off however your smart device can be switched to silent mode silence shutter release and screen press sounds.

The Osmo has not been activated yet. Please activate the device.

Photos will be automatically cached to media library, but video auto-cache is not set to cache by default and can be switched on.
If mobile device cache memory is full or if video capacity is larger than 2GB, the video also will not auto-cache.
If the length of the video is less than 6s, the video will not auto-cache.

Long exposure can be set in the camera settings beneath shutter speed in the DJI GO app. Go to S or M mode, then choose a slower shutter speed.

Time-lapse photos are stored in the directory under Micro SD Card DCIM\TIMELAPSE.

No, the Osmo will automatically flip the image so it’s oriented correctly.

The camera cannot track save times by itself and requires connection to the DJI GO App. Connecting to a mobile device before shooting is recommended.

The camera will automatically adjust its field of view to 52° in Slow Motion Mode.

Android: Media Library – Picture – Select Photo – Share Photo – Save.
The Panoramic Composite Photo can also be viewed in the Playback but cannot be downloaded.
IOS: Media Library – Picture – Select – Download.

No, because the camera will reset when switching from NTSC to PAL.

The screen cannot zoom in, but you can zoom in the photo during playback.

Upgrade logs are stored under ‘Micro SD-Misc - log - OSMO_FW_LOG_AB_txt’.

The upgrade package is saved in the DJI GO app. The upgrade package will be sent to the camera via Wi-Fi, and then sent to the Micro SD Card.

The Extension Rod supports the bicycle mount, the universal mount, the mobile-phone holder, the extension rod and other accessories. The expanding arm can also be used by itself.

The screw type of the Extension Rod and the tripod is the British standard 1/4-20UNC. The Osmo cannot be installed directly onto the tripod, the Extension Rod is required.

No, the Universal Mount is only required if you want to add additional accessories, such as an external microphone. The universal mount can be attached to the same rosette mount used by the mobile phone holder. It can be installed using 1/4 inch screws.

The maximum speed is 100 km/h. If the speed is larger than it, it is recommended to mount it in the vehicle.