Weight (including battery and propellers) | 1280 g |
---|---|
Diagonal Size (Excluding Propellers) | 350 mm |
Max Ascent Speed | 5 m/s |
Max Descent Speed | 3 m/s |
Hover Accuracy | Vertical: +/- 0.1 m (when Vision Positioning is active) or +/-0.5 m Horizontal: +/- 0.3 m (when Vision Positioning is active) or +/-1.5 m |
Max Speed | 16 m/s (ATTI mode, no wind) |
Max Service Ceiling Above Sea Level | 6000 m (Default altitude limit: 120 m above takeoff point) |
Operating Temperature | 0°C to 40°C |
GPS Mode | GPS |
Max Flight Time | Approx. 25 minutes |
Controllable Range | Pitch -90° to +30° |
---|---|
Stabilization | 3-axis (pitch, roll, yaw) |
Operating Frequency |
|
---|---|
Max Transmission Distance |
|
Operating Temperature | 32° to 104° F ( 0° to 40° C ) |
Battery | 2600 mAh LiPo18650 2S |
Transmitter Power (EIRP) |
|
Operating Voltage | 300 mA @7.4 V |
Capacity | 4480 mAh |
---|---|
Voltage | 15.2 V |
Battery Type | LiPo 4S |
Energy | 68 Wh |
Net Weight | 365 g |
Operating Temperature | 32° to 104° F ( 0° to 40° C ) |
Max Charging Power | 100 W |
Sensor | Sony EXMOR 1/2.3" CMOS |
---|---|
Lens | FOV 94° 20 mm (35 mm format equivalent) f/2.8, focus at ∞ |
ISO Range |
|
Shutter Speed | 8s - 1/8000s |
Image Max Size | 4000×3000 |
Still Photography Modes |
|
Video Recording Modes |
|
Supported SD Card Types |
|
Max Video Bitrate | 60 Mbps |
Supported File Formats | FAT32 ( ≤ 32 GB ); exFAT ( > 32 GB ) |
Operating Temperature | 32° to 104° F ( 0° to 40° C ) |
Photo | JPEG, DNG |
Video | MP4, MOV (MPEG-4 AVC/H.264) |
Velocity Range | Less than 8 m/s (2 m above ground) |
---|---|
Altitude Range | 30 cm-300 cm |
Operating Range | 50 cm-300 cm |
Operating Environment | Surface with clear pattern and adequate lighting (Lux > 15) |
Voltage | 17.4 V |
---|---|
Rated Power | 57 W |
Mobile App | DJI GO |
---|---|
Live View Quality | 480P @ 30fps |
Required Operating Systems |
|
Recommended Devices |
*Support for additional Android devices available as testing and development continues. |
EIRP | 100mW |
Power Spectral Density | 6.9mW/MHz |
Live View Working Frequency | 2.4GHz ISM |
Latency | 220ms (depending on conditions and mobile device) |
iOS Version v3.1.62.
Requires iOS 8.0 or later. Compatible with iPhone 5s, iPhone SE, iPhone 6, iPhone 6 Plus, iPhone 6s, iPhone 6s Plus, iPhone 7, iPhone 7 Plus,iPod touch 6,iPad Pro, iPad Air, iPad Air Wi-Fi + Cellular, iPad mini 2, iPad mini 2 Wi-Fi + Cellular, iPad Air 2, iPad Air 2 Wi-Fi + Cellular, iPad mini 3, iPad mini 3 Wi-Fi + Cellular, iPad mini 4, and iPad mini 4 Wi-Fi + Cellular. This app is optimized for iPhone 7, iPhone 7 Plus.
Android Version v3.1.59.
Requires Android 4.4 or later.Compatible with LG V20, VIVO X9, OPPO R11, Google Pixel, Nexus 6P, Huawei P9, Huawei MATE 9, Samsung Galaxy Tab S2, Samsung Galaxy S5, Samsung Galaxy S6 Edge, Samsung Galaxy S6, Samsung Galaxy S7, Samsung Galaxy S7 Edge, Samsung Galaxy S8, Samsung Galaxy S8+, Samsung Galaxy Note 8, Samsung Galaxy Note 5, MI 6, MI5.
*Support for additional Android devices available as testing and development continues.
Option 1: Turn on the remote controller, then, while holding down the C1 and C2 buttons on the back of the remote controller, press the camera settings dial to reset.
Option 2: Flick the flight mode switch back and forth until the remote controller status indicator blinks red and green. This shows that the reset is in progress. Wi-Fi download reset is successful when the remote controller status indicator turns solid green.
The Phantom 3 4K is linked to the remote controller by default. Re-linking is only necessary if the remote controller is replaced.
To link a new remote controller:
1) Turn on the remote controller and connect to your mobile device.
2) Launch the DJI GO app.
3) Turn on the Intelligent Battery.
4) Enter “Camera” and tap on the remote controller icon and then tap the “Linking RC” button. The remote controller is now ready to link. The Remote Controller Status Indicator will blink blue and the controller will beep.
5) Locate the linking button on the side of the aircraft and press it to link. The Remote Controller Status Indicator LED will display a solid green once the remote controller has been successfully linked to the aircraft.
The remote controller is CE compliant by default and switching between CE and FCC is automatic based on aircraft location as determined by the DJI GO app.The CE compliant remote controller has an effective signal range of 0.31 miles (500 m) in open spaces.The FCC compliant remote controller has an effective signal range of 0.74 miles (1200 m) in open spaces. Be aware of your flying distance as the aircraft will enter Failsafe Return to Home if it flies beyond transmission range.
The Phantom 3 4K comes with a 16 GB Micro SD card and supports Micro SD cards with a capacity of up to 64 GB. UHS-1 or Class 10 Micro SD cards are recommended to minimize delay when reading or writing high resolution image files. Do not insert or remove the Micro SD card when the Phantom 3 4K is turned on.
1) Switch on the remote controller.
2) Turn on the aircraft.
3) On your mobile device, select “PHANTOM3_XXXXXX”“from your Wi-Fi network list, and enter the default password “12341234”.
4) Launch the DJI GO app and enter Camera View. A video signal from the aircraft’s camera indicates that the aircraft has established a connection to the Wi-Fi video downlink successfully.
1) Make sure it is sufficiently charged before each flight.
2) Lock the mobile device holder firmly in place to avoid slipping.
3) Unfold the antennae and keep them perpendicular to the Phantom for optimal transmission quality. Do not point the antenna at the Phantom.
4) Repair or replace the remote controller if damaged. A damaged remote controller antenna will greatly decrease performance. If a remote controller is replaced, please see Question 3 of this FAQ: How do I link the remote controller?